Two NP-F batteries and a USB-C power bank laid out next to a 7 inch monitor

Prev post

Next post

A BNC SDI cable and an HDMI cable side by side beside a 7 inch camera monitor
A Shinobi monitor showing a false color exposure map of a portrait on a camera rig

False Color, EL Zone and LUTs on an Atomos Shinobi: Exposure Guide

A practical guide to false color, EL Zone, zebra and LUT preview on Atomos Shinobi monitors.

False color, EL Zone and LUTs are the three monitor tools that fix the most exposure mistakes before you press record. Use false color or EL Zone to see exactly how bright each part of the frame is, and load a LUT to preview the final look while still shooting in log. All Atomos Shinobi monitors support LUTs, and every model except the Shinobi GO adds EL Zone and ARRI false color. This guide explains what each tool does and how to use it.

Why camera screens mislead you

Log footage looks flat and grey on the camera's screen, and a bright outdoor screen fights reflections. Both make judging exposure by eye unreliable. A monitor with measurement tools replaces guessing with numbers and colours you can read at a glance. You see where highlights are about to clip, whether skin sits in the right range, and whether the shadows hold detail.

The tools at a glance

Tool What it shows Best for
Focus peaking Coloured edges on sharp areas Checking focus on a moving shot
Zebra Stripes over areas above a set brightness Protecting highlights
False color A colour map of brightness across the frame Judging overall exposure
EL Zone Colours tied to exact exposure values in stops Repeatable, precise exposure
Waveform and parade A graph of brightness, or of each colour channel Balance, contrast and clipping
Vectorscope Colour saturation and hue Skin tones and colour casts
LUT preview An approximation of the graded image Judging the look while shooting log

All Shinobi monitors include focus peaking, zebra, zoom at 4:1, 2:1 and 1:1, waveform, RGB parade and vectorscope, according to Atomos.

Zebra: the quickest check

Zebra overlays diagonal stripes on any part of the image brighter than the level you choose. On the Shinobi 7 II the threshold adjusts from 50 to 105 percent. A common habit is to set it near the point where highlights start to clip on your camera, then lower the exposure until the stripes only touch the brightest speculars. It is fast, and it does one job well.

False color: see the whole frame

False color paints each brightness band in a different colour, so the image reads like a heat map. Shadows might be blue or purple, mid tones green, skin a particular band, clipped highlights red. Instead of looking at the picture, you look at where colours sit. Atomos includes its own false color on every Shinobi and adds ARRI false color on the Shinobi II, 7 II and 7 RX.

The method is simple. Switch false color on, point at a face or a grey card, and move the exposure until that area lands in the band you want. Then switch it off and shoot. Check the key shown on screen the first time, because each scheme assigns colours differently.

EL Zone: exposure in stops

EL Zone is a false color system based on stops of light rather than rough IRE ranges. Each colour stands for a specific exposure value, in the same way your camera sees it. Atomos describes it as a precise and consistent way to expose correctly every time. It is on all Shinobi monitors except the GO.

A practical use: pick the zone you want skin to sit in and keep it there from shot to shot. Because the zones are fixed, two cameras or two days of shooting match more closely, which saves time in grading.

LUTs: preview the look in log

Shooting in log gives you the most room in post but looks flat on set. A LUT, or Look Up Table, is a file that maps the flat log image to a viewable one. The Shinobi monitors receive a log signal from the camera and apply a real time LUT so you see an approximation of the final Rec.709 image. This helps clients, directors and you judge colour without reading a flat picture.

To load your own, copy .cube files to an SD card and insert it into the monitor. The Shinobi 7 II supports .cube files with 17 and 33 points, and Atomos lists 3D and 1D LUT support across the range. The LUT only changes what you see on the monitor: your camera still records the original log image unless your camera itself applies a LUT.

Use the LUT for the look and false color or waveform for the exposure. If a reading looks odd, switch the LUT off and check again on the plain log image.

A simple exposure routine

  1. Set your camera's log profile and confirm the monitor reads the matching gamma.
  2. Turn on peaking and check focus with a zoom punch in.
  3. Turn on false color or EL Zone, expose the subject into the band you want, then switch it off.
  4. Use zebra to guard the brightest highlights during the take.
  5. Load your LUT to judge the look and show clients a clean image.

Framing tools that save a reshoot

Exposure is only half of what goes wrong on set. The Shinobi range also carries framing aids:

  • Frame guides. The Shinobi 7 II lists cine presets for 2.41, 2.35, 1.91, 1.9, 1.85 and 16:9, plus social presets for 9:16, 4:5, 2:3, 1:1, 5:4, 4:3 and 3:2. That helps when one shoot must feed a film, an Instagram reel and a vertical ad.
  • Safe areas and grids. SMPTE safe title areas and a grid keep subjects and titles inside the area people will see.
  • Anamorphic desqueeze. If you shoot with an anamorphic lens, the monitor can stretch the squeezed image back to normal so you compose on the right shape. The 7 II lists ratios including 2x, 1.8x, 1.5x and 1.33x.
  • Display flip. Horizontal and vertical flip, handy when the monitor is upside down on a rig or you shoot through a mirror.

Calibration: trust what you see

A monitor is only useful for judging colour if it is accurate. Atomos states that the Shinobi II, 7 II and 7 RX can be calibrated with Calibrite probes, and the spec pages list on device calibration or computer driven calibration. If you grade or match colour across cameras, calibrate on a schedule and before an important shoot.

A checklist for the night before

  • Update firmware, and keep the .cube LUTs you need on a spare SD card
  • Confirm the monitor reads the same log profile your camera outputs
  • Set the frame guide for your delivery format
  • Check your false color or EL Zone key so you know what each colour means
  • Pack a spare cable and a charged battery

Picking a Shinobi for these tools

For a full toolset including EL Zone and ARRI false color, choose the Shinobi II, the Shinobi 7 II or the Shinobi 7 RX. The Shinobi GO has the basic tools but not EL Zone or ARRI false color. Our range guide compares all four. If your card storage is part of the workflow, our memory card guide helps with the camera side.

Frequently asked questions

What is the difference between false color and EL Zone?
Both colour the image by brightness. Traditional false color uses rough IRE ranges. EL Zone assigns colours to exact exposure values in stops, which makes results more repeatable.

Does the Shinobi GO have EL Zone?
No. EL Zone and ARRI false color are available on the Shinobi II, 7 II and 7 RX. The GO has the Atomos false color and the other standard tools.

Can I use my own LUT on a Shinobi?
Yes. Load .cube files from an SD card. The monitor uses them for display, with a log signal from the camera.

Does a LUT change my recorded footage?
Not on the monitor alone. The LUT is applied to the display. Your camera records its own image unless you set it to bake in a look.

Back to blog

Newsletter

Add subheading here

Tags

Social media